2017 Geeetech 3D Printer Kit GT2560 Controller board+LCD 2004+5pcs A4988 Driver

Description

BEST SERVICE BEST PRICE
Description
Are you still annoyed without a kit for your excellent experiment idea? Here's the chance! We offer a full set of experiment equipments for you.
1.GT2560
GT2560 is a compact board that is integrated with the mighty function of the Arduino Mega2560+Ultimaker.
The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but has more premium features: the streamlined interfaces effectively avoid the unnecessary troubles, well-regulated compaction of components highly integrated saves more space and easier to be mounted on most applications.
5 stepper motors, swappable driving modules, mighty ATmega2560 processor with 256k memory, 16MHz operating frequency, high-performance USB serial converter FT232RQ, all these make the GT2560 an ideal option for a 3D printer control board. What’s more, GT2560 can run over 12V and output 90W to a MOSFET, which gives higher torque and higher rotation rate.
Features：
1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker, The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but also features compact size, more convenient connection, and more stable.
2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ.
3. The power pack: operating voltage is 12V-24V; double power supply design feeds for heatbed and logical part separately. The current is 15A for heatbed and 10A for other parts. The cooling fan can support 12V
4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse.
5． 3 12v fan output and one PWM output for LED or other lighting equipment.
6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation and stable operation.
7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate.
8. 3 temperature sensor input (100k thermistor is recommended)
9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which you can print without your PC.
10. The firmware is the prevalent Marlin, which is known for stability, usability, and high-performance.
GT2560 VS Ramps1.4+ mega 2560
Compared with Ramps1.4+ mega 2560, GT2560 has the following merits：
1. Further compacted volume and space-saving.
2. Integrated peripherals ensure more stable connection.
3. Added heat sink provide better heat dissipation for MOSFET
4. Separate control for fan and extruder
5. Support LCD2004 and LCD12864 without using adapters
Here is a detailed comparison between GT2560 and Ramps1.4+ mega 2560:
3D control board
GT2560
Ramps1.4+
mega 2560
Main control chip
ATMEGA2560
ATMEGA2560
dimension
110X80X25
110X60X40
Extruders
2
2
thermistor
3
3
Endstop
6
6
Controllable fan
1
1(if you use dual extruders, this is not applicable)
uncontrollable fan
3
3
Stepper motor driver
5
5
Need Stack board
no
yes
LCD2004 and 12864
Yes
Yes(needing the adaptor
)
Hardware resources
12V/24V 15A and 12/24V 10A Power Supply
1 power port for heatbed and 2 for extruder
5 stepper motor input, (3 for X/Y/Z axis, and 2 for extruders)
Extended LCD & SD card interface
6 endstop input(X-MIN ,Y-MIN ,Z-MIN and X-MAX ,Y-MAX ,Z-MAX)
3 input for thermistor (TEMP1, TEMP2 and TEMP3)
3 input for12V cooling fan
1 PWM output
Dimension: 109mm*78mm*22mm
1.2 Software Resources
Compiling environment: Arduino IDE
Firmware: Marlin
Host software：printrun Repetier-Host
2. Interfaces
2.1 Interface Layout
2.2 Interface specifications
1.DC IN： 12V-24V 15A and 12-24V 10A
2.HOT_BED:heat bed
3.HEATER1: power supply for extruder 1
4.HEATER2: power supply for extruder 2
5.LCD ENCODER： LCD panel
6.SD Card
7. X_MIN/X_MAX/Y_MIN /Y_MAX /Z_MIN /Z_MAX: 6 end stop input, XH2.54-2Pin
8. TEMP1: temperature sensor for extruder 1, XH2.54-2Pin
9. TEMP2: temperature sensor for extruder 2, XH2.54-2Pin
10. TEMP3: temperature sensor for heatbed , XH2.54-2Pin
11. X,Y,Z：Stepper motors for X, Y, Z axis, XH2.54-4Pin
12. EXT1, EXT2(A)：Stepper motors for extruder 1 and extruder 2, XH2.54-4Pin
13. FAN1，FAN2，FAN3：3 12V cooling fans, PH2.0-3Pin
14.1 PWM: PWM output for cooling fan, FAN:PH2.0-3Pin
2.LCD 2004
This is a basic 20 character by 4 line dot matrix LCD display controller module designed for different 3D printer motherboard.With different adaptor,you
can connect the smart LCD with Geeetech RAMPS1.4,Sanguinololu,Megatronics and Rambo,then make your printer stand alone and print without PC.
You could just use the cable to connect it with Geeetech Ultimaker,no adaptor needed.
Features:
Display: 20 Characters X 4 lines
Module Size: 98.0 X 60.0 X 14.0
Viewing Area: 76.0 X 25.2
Character Size: 2.95 X 4.75
Controller IC: S6A0069 or equal
Supply voltage: 5V
Package List:
1 pcs GT2560 board
1 x
LCD 2004 display controller for 3D printer(
Without Adaptor, the blacklight is Yellow
)
5 X Pololu A4988
5 X heatsink
2 x sticker
Payment
1.We accept PayPal only.
2.Payment must be received within 7 business days of auction closing.,or a unpaid case will be opened.
Delivery details
1.Standard shipping carrier is ePacket with tracking code for United States address,delivery within 7-14 busienss days.
2.For outside US address,standard shipping carrier is Hong Kong Post without tracking code,delivery within 25-30 business days. We provide a free tracking for order above 30USD. For the order below 30USD, if you choose "Economy Int'l Shipping", there is no tracking number by Normal mail. If you choose "Standard Int'l Shipping", there is a tracking number by Registered mail.
3.Express shipping like DHL,Fedex,UPS,TNT is also avaiable if you are willing to pay extra. DHL is our standard shipping carrier for Expedited shipping,please contact us if you want a different carrier.
4.For orders overweight (above 2kg), we must use Express shipping, it normally takes 5-7 busienss days to deliver. We will contact you if your orders are overweight, please note that buyer are resposible for the shipping charge.
Terms of sales
1.Customs duties or taxes are buyer's resposibility for all of the listings.Please check with your local customs office if you have any doubts.
2.Please confirm you are putting a correct and complete shipping address here.You are resposible for extra charge if your package been returned because of wrong address.If packages return because of wrong address,you will have to bear extra cost of shipping.
Contact us
1.We are always here for you,offering friendly, comprehensive customer service every step of the way. Please follow the good eBay practice to contact us if any doubts and problems.We sincerely hope our item and customer service can give you the BEST BUYING EXPERIENCE on eBay.
2.We greatly appreciate your POSITIVE feedback.
Please do NOT leave negative or neutral feedback without any contact.